Frequent question : how to reset oil change message on 2008 ford explorer?

Also know, how do you reset the oil change light on a 2008 Ford Explorer? Turn the ignition to the “RUN” position. Enter “SYSTEM CHECK” menu and “OIL % OIL LIFE OK” will be displayed. Press “RESET” button, “HOLD RESET IF NEW OIL” will be displayed. Press and hold the “RESET” button for more than 2 seconds.

Also, how do you reset the oil change light on a Ford Explorer? Turn the ignition to the ON position. Do not start the engine. Press and release the “Select/Reset” stem button on the instrument panel to toggle the options until the “Hold Reset For Setup Menu” option appears. Press “Select/Reset” to toggle the options until the “Hold Reset if New Oil” option appears.

Likewise, how do I clear my oil change message?

1. Press and hold the reset button.
2. Turn the ignition back to the ON position while holding the reset button.
3. Watch the oil change or maintenance light carefully.
4. Allow the light to blink ON and OFF for a few seconds, then release the reset button and turn the ignition OFF.

People ask also, how do you reset the oil change light on a 2009 Ford Explorer?

1. Press and release the SETUP button to display “Oil Life XXX% Hold Reset = New”
2. Press and hold the RESET button for 2 seconds and release to reset oil life to 100%

How do you reset the change oil light on a 2007 Ford Explorer?

1. Press the SETUP button until the display reads “Press Reset To Begin System Check”
2. Press the RESET button to display “Hold Reset If New Oil”
3. Press and hold the RESET button for 2 seconds and release.
4. The oil life is now set to 100%

How do I reset my Ford Explorer?

1. Open the hood: release the primary latch by pulling the release lever under the steering wheel near the floor board.
2. Disconnect the negative battery terminal.
3. Wrap the negative clamp in a towel.
4. Leave the negative battery cable off for a minimum of five minutes.

How do you reset the oil change light on a 2010 Ford Explorer?

1. Get in the car and turn key to the on position.
2. Go to the SETUP MENU HOLD RESET screen.
3. Press and hold the SELECT/RESET button.
4. Enter to the RESET FOR SYSTEM CHECK menu.
5. Scroll to OIL LIFE.
6. Hold down the SELECT/RESET button.

How do you reset the oil life on a 2011 Ford Explorer?

1. Switch the ignition over to the on position.
2. Go to the SETTINGS menu.
3. Scroll and select VEHICLE.
4. Scroll down to OIL LIFE RESET.
5. Press and hold the OK button.
6. Shut the vehicle off and then start it back up and check the oil change light should be gone.

How do you reset car sensors?

How do I reset my service light?

Why does my car says change oil after I changed it?

The final common cause of an illuminated oil light, even after an oil change, is probably the most problematic. The oil pump may not be circulating enough oil to keep the engine’s parts lubricated and functioning properly, which can in turn cause multiple engine issues.

What does the wrench light mean on a 2010 Ford Explorer?

If You see the wrench light turn on in the dash of Your 2010 Ford Explorer this means that Your ECU has detected a fault. I recommend getting off the road as soon as possible because continuing to drive can cause more damage to Your SUV.

What oil does a 2008 Ford Explorer take?

Ford recommends 5 quarts of 5W30 synthetic formulated oil for the 4.0L V6 SOHC engine in the 2008 Ford Explorer. The 4.6L V8 engine option for the 2008 Explorer uses 6.3 quarts of 5W20 synthetic oil.

How do you reset the wrench light on a 2008 Ford Escape?

Step 1: With the car off press and hold the trip reset button. Step 2: Wile still holding the button press the start button twice without your foot on the brakes. Step 3: A yellow triangle indicator next to the speedometer should flash a few times meaning that the wrench light has been reset.