- Resetting the fault codes and performing a road test.
- Replacing the oil and filter using the proper oil viscosity for the engine.
- Repairing or replacing the wiring to the camshaft oil control valve for bank 1 exhaust camshaft.
Furthermore, what does the code P0014 mean? What Does Code P0014 Mean? The variable valve timing system increases fuel economy and engine performance by regulating when the intake and exhaust valves are opened and closed. … When trouble code P0014 is set, it means that the exhaust camshaft in Bank 1 is more advanced than the ECM has told it to be.
Additionally, how do I fix code p0014?
Another frequent question is, how do you reset the check engine light on a Hyundai? To reset the check engine light in your 2017 hyundai elantra vehicle, try disconnecting the battery cables for 10-15 minutes and then reconnecting them, or turn your ignition key to the “on” and then “off” position twice, followed by starting the engine and the light should disappear.
Likewise, can low oil cause a P0014 code? Sludge buildup can cause a P0014 trouble code Sludge is caused by running the engine at low oil levels, neglecting oil changes or going too far on an oil change, poor PCV operation or using a poor quality oil. Change the oil, clear the code and drive the vehicle.
- How much does it cost to fix code P0014?
- Can I drive with a bad camshaft position sensor?
- Can too much oil cause P0014?
- How much does it cost to replace a camshaft sensor?
- Where does the camshaft position sensor go?
- How do I reset my Hyundai Sonata?
- How do you reset the check engine light on a Hyundai Sonata?
- How do I clear my check engine light without a scanner?
- Will an oil change fix P0014?
- How do I fix the timing on my camshaft position?
How much does it cost to fix code P0014?
It can be as affordable as a $50 oil change, a $100 sensor replacement or it can be a $1,000 timing job.
Can I drive with a bad camshaft position sensor?
Yes, it is safe to drive with a bad camshaft sensor. However, the performance of your engine will not be as good and fuel consumption may increase. … In some cases, the camshaft may need replacement if there are any other symptoms of failure on this component.
Can too much oil cause P0014?
Causes of Code P0014 There are a few common causes of P0014 code that could be the source of the problem, including: The engine oil viscosity is too high and blocking passage to the camshaft. The flow of oil to the engine must be constant, which enables it to run smoothly.
How much does it cost to replace a camshaft sensor?
To replace a camshaft position sensor, you can expect to pay anywhere from $95 to $200. Parts alone will run about $25 to $100. Labor costs will be in the range of $70 to $100 for professional replacement. Expect to pay more if you have a luxury vehicle or are having your local car dealership perform the replacement.
Where does the camshaft position sensor go?
The camshaft position sensor is always located near the camshaft, often at the top of the valve cover, but it can also be installed from the side of the cylinder head.
How do I reset my Hyundai Sonata?
How do you reset the check engine light on a Hyundai Sonata?
There are different ways to reset the check engine light on the 2018 Hyundai Sonata but sometimes it will just go off by itseLFAfter driving for a while. Another way that You can reset the check engine light on the vehicle is to unplug the battery, wait for about 20 minutes and then plug it back in.
How do I clear my check engine light without a scanner?
Will an oil change fix P0014?
In layman terms, P0014 means it’s a generic engine code that refers to an advanced or over-advanced exhaust camshaft in bank 1. Replacing your oil and filter usually fixes the P0014 OBD2 Trouble Code! If that doesn’t work, you’ve likely got an oil control solenoid that needs to be replaced.