Jannah Theme License is not validated, Go to the theme options page to validate the license, You need a single license for each domain name.
Ford Explorer

How to reset the oil change light on a 2008 ford explorer?

Turn the ignition to the “RUN” position. Enter “SYSTEM CHECK” menu and “OIL % OIL LIFE OK” will be displayed. Press “RESET” button, “HOLD RESET IF NEW OIL” will be displayed. Press and hold the “RESET” button for more than 2 seconds.

Also know, how do you reset the oil change light on a Ford Explorer? Turn the ignition to the ON position. Do not start the engine. Press and release the “Select/Reset” stem button on the instrument panel to toggle the options until the “Hold Reset For Setup Menu” option appears. Press “Select/Reset” to toggle the options until the “Hold Reset if New Oil” option appears.

Also, how do you reset the oil change light on a 2009 Ford Explorer?

Likewise, how do I reset my oil change light?

People ask also, how do I reset my Ford Explorer?

  1. Open the hood: release the primary latch by pulling the release lever under the steering wheel near the floor board.
  2. Disconnect the negative battery terminal.
  3. Wrap the negative clamp in a towel.
  4. Leave the negative battery cable off for a minimum of five minutes.
  1. Press and hold the SELECT/RESET stem for more than two seconds. Oil life is set to 100% and OIL LIFE SET TO 100% is displayed.
  2. Once OIL LIFE SET TO 100% is displayed, release, press and hold the.
  3. After setting the oil life start value, press the SELECT/RESET stem.

Contents

How do you reset the change oil light on a 2007 Ford Explorer?

How do you reset the oil life on a 2011 Ford Explorer?

  1. Switch the ignition over to the on position.
  2. Go to the SETTINGS menu.
  3. Scroll and select VEHICLE.
  4. Scroll down to OIL LIFE RESET.
  5. Press and hold the OK button.
  6. Shut the vehicle off and then start it back up and check the oil change light should be gone.

Why is my change oil light still on?

If your oil light stays on even after changing your engine oil, you’re going to want to check the sensor first to rule out a malfunctioning sensor as the cause. Dirt and other particles can make their way into the oil pump, causing the sensor to falsely identify oil issues. … The next common cause is low oil pressure.

Why is my engine light on after oil change?

These lights can signal something serious or something as simple as a loose gas cap. … Oil changes are essential maintenance for your car but it won’t do anything that could trigger your check engine light to come on. If you notice the light after an oil change, something else is wrong.

Why does my change oil light keep coming on?

When the oil light on your dashboard comes on, it might mean your vehicle has low oil pressure. This drop in oil pressure could be a sign of a few things: you are low on oil, your oil is dirty, or you have an oil leak.

Where is the reset button on a Ford Explorer?

To reset the fuel light on a ford explorer you will need to access the fuel reset switch which is located in the glove box or in the foot well of the passenger seat area, press that switch and the fuel system will be reset.

How do you clear the code on a Ford Explorer?

The first way is to connect an OBD-II scan tool and clear the trouble codes, so long as they are not permanent codes. Another is to disconnect the battery for at least 10 to 15 minutes. Once the power is reconnected, the light should have reset.

Why has my Ford Sync stopped working?

Reset Connection In Sync On your phone, turn Bluetooth Off, then On. … On SYNC, turn Bluetooth Off, then On. Press the Phone button > scroll to System Settings > Press OK > scroll to Bluetooth Devices > Press OK > select Off > select On. If this does not work, continue to steps 3 and 4.

What does the wrench light mean on a 2010 Ford Explorer?

If You see the wrench light turn on in the dash of Your 2010 Ford Explorer this means that Your ECU has detected a fault. I recommend getting off the road as soon as possible because continuing to drive can cause more damage to Your SUV.

How do you reset the oil life on a 2010 Ford Sport Trac?

  1. Turn the ignition to run (one position before starting engine).
  2. Press SETUP to display OIL LIFE %.
  3. Press RESET button to display “HOLD RESET IF NEW OIL”.
  4. Press and hold the RESET button for more than two seconds.

See also:   Frequent question : how to replace the blend door actuator on a 2004 ford explorer?
Back to top button

Adblock Detected

Please disable your ad blocker to be able to see the content of the page. For an independent site with free content, it is literally a matter of life and death to have ads. Thank you for your understanding!