Jannah Theme License is not validated, Go to the theme options page to validate the license, You need a single license for each domain name.
Ford Explorer

How to reset anti theft system 2000 ford explorer?

Allow the driver’s door to be locked for at least 30 seconds, then use the key in the door cylinder to unlock it. This should clear anything that is wrong with the alarm system.

Also know, how do I get my Ford Explorer out of theft mode? First, go to the driver’s side of Your vehicle, and insert the key into the lock. Turn the lock to the right, or to the unlock position. Hold this position and count for 25 to 40 seconds. Doing this will bypass the anti-theft system.

Likewise, how do you reset the antitheft on a 2001 Ford Explorer? Press the panic button one time. Now, go to the driver’s side of Your car, and get inside. Place Your physical key into the ignition key hole, and turn it to the on position three times in a 10 second period. Now, start the engine, and the anti-theft system should be reset.

Also, how do I reset my Ford anti-theft system with one key? Put one into the ignition, and turn it to “ON”. Cycle it back to “OFF” and remove. Immediately insert the second key (within 5 seconds) and cycle it to “ON” and “OFF” as well. Insert the original key back within 10 seconds, leave it “ON” for one second, and then cycle back to off.

People ask also, how do you reset the computer on a 2000 Ford Explorer?

  1. Open the hood: release the primary latch by pulling the release lever under the steering wheel near the floor board.
  2. Disconnect the negative battery terminal.
  3. Wrap the negative clamp in a towel.
  4. Leave the negative battery cable off for a minimum of five minutes.
See also:   What size is the axle nut on a 2005 ford explorer?

Step 1: Insert the key into the door lock. Use the side door on the driver’s side and the physical key even if there is a keyless entry system on the car. Step 2: Turn the vehicle key to unlock the car door without releasing it. Hold the key for 30 seconds in the position.

Contents

Will disconnecting battery reset anti theft?

One last thing you can try if your car alarm is going off and you can’t get it to stop, but you can get under the hood is to disconnect the battery. By unplugging the battery for a few minutes, it will also reset the computer. All you have to do is disconnect the positive or negative terminal and wait.

How do you bypass the anti theft system on a 2000 Ford Explorer?

Allow the driver’s door to be locked for at least 30 seconds, then use the key in the door cylinder to unlock it. This should clear anything that is wrong with the alarm system.

How do I get my 2002 Ford Explorer out of theft mode?

To begin, turn the key in the ignition as if You were trying to start the engine. The engine won’t start since the anti-theft system has been activated. Allow the key to fall back into the ON position so the dashboard lights and radio still work. Leave the key like this for at least 10 minutes.

How do I reset my anti theft system?

Exit the car with all doors closed and the windows rolled up. Also close and any rear doors such as the trunk, rear hatch and front hood. Lock the car using the drivers side lock and walk away from the car at least ten feet. Wait for fifteen minutes and unlock the door, this should reset the security system.

How do I get my Ford Focus out of anti theft mode?

One way is to put the physical key in the lock, and then turn it to the unlock position. Do this, without moving it away from that unlock position for about 30 seconds. After that, You can unlock the car and start the engine. This will trigger a reset of the system.

What triggers the anti theft system in car?

The Anti-theft alarm system works with the help of sensors installed in and around the vehicle. An impact or the movements inside the car activates the sensors. This, in turn, triggers the Anti-theft alarm system and sounds the alarm. The alarm goes off and alerts the owner/people.

How do I bypass Ford Anti theft system?

Locate the override button on the alarm box, beneath the driver’s side of the dashboard. Press the button and hold it in until the alarm beeps one time. The LED light for the alarm should stop blinking, indicating the antitheft system is disabled.

How do I reset my Ford Explorer computer?

  1. Open the hood of the Ford. Loosen the lock nut located on the negative battery cable connector with a socket and ratchet.
  2. Wait for 20 minutes while the PCM bleeds off the electricity it stores for backup power. Once the power drains from the PCM, it resets.

How do you reset a transmission control module?

  1. Step 1: Turning Key Position.
  2. Step 2: Press gas pedal.
  3. Step 3: Keep Waiting.
  4. Step 4: Turning the Key Off.
  5. Step 5: Releasing Gas Pedal.
  6. Step 6: Wait Again.
  7. Step 7: Ready.
  8. Identification.

How do you reset the transmission control module on a Ford Explorer?

  1. Step 1: Start the vehicle’s engine.
  2. Step 2: Put the vehicle’s gearbox in neutral.
  3. Step 3: Put the vehicle in park mode.
  4. Step 4: Again start your car.
  5. Step 5: Turn off the vehicle.
  6. Step 6: You are ready!

Back to top button

Adblock Detected

Please disable your ad blocker to be able to see the content of the page. For an independent site with free content, it is literally a matter of life and death to have ads. Thank you for your understanding!